I really like the staked furniture method. I like the design process and the making. Consequently, I have several staked projects on the “to-do” list. Since I don’t own or plan to add a lathe to my shop, the tapered, octagonal leg is my leg design of choice. I also typically design my projects with proportions. So I am faced with a choice. Either design new leg proportions for each project or come up with a standardized method for making the legs.
The legs for the majority of my planned projects, even with unique proportions applied, are so similar that there is virtually no visual difference between them. So a standard layout method should be just fine for most of my planned projects. As a bonus, there should be less chance or error with an internalized standard method…at least in theory.
In my last post I discussed the “octagonizer”(aka spar gauge). A simple proportional gauge that aids in the speedy layout of an octagon. It’s a handy little thing but, in addition to laying out an octagon, I wanted to find a way to proportionally taper my legs as well. So I explored several different ways of solving the problem, but kept coming up short. Eventually I hit on a solution though. I had been expecting the solution to be complex and had continually overlooked a simple solution.
I recently built a couple of footstools, here and here. While laying out the legs I played around with a few different methods. CW presents two ways of making an octagonal, tapered leg in his “The Anarchist’s Design Book”. Those methods work fine, but still rely on dimensions as well as two rounds of layout. The first step in cutting removes half of the layout marks. So I pulled out some scrap paper, compass and straightedge. That is when I hit upon this:
Doesn’t look like much, but it has a proportional relationship! The smaller, rotated square is 5/7th the larger, original square. So I tried laying out and cutting a leg using this rotated square method. Worked great! One round of layout and cutting was all that was needed. So now I had a proportional way of laying out my legs. Now, can I make it more standardized and faster to layout?
It was at this point that I became aware of the “octagonizer” and explored how to make it. While working on the layout for the “octagonizer” something jumped off the page at me. The “octagonizer” is really just a proportional gauge. I should be able to add a pin 1/7th the distance from the guide pins and gauge the taper for my leg. Sure enough, worked like a charm. Hey, I need the center marked too. Might as well add a pin for that too!
So I redesigned the gauge to produce all of the information I need to layout an octagonal, proportionally tapered leg for staked furniture. It marks the corner of the full width octagon, the 1/7th taper for each face, the center of the stock face and the length of the tapered tenon area. Oh, did I not mention that I designed the gauge so that it’s full length is equal to the length of the tapered tenon area? This one gauge gives me all the distances I need on stock up to 1-7/8″(48mm) thick in section. As well as a consistent 7:5 taper no matter the length of the leg. Not too shabby for a scrap of wood and three nails! Thus the OCTA-LEG-PRO was born.
I first mark the tenon area using the full length of the gauge.
Then I register the gauge on the stock and press down firmly to generate three gauge marks.
Depending on the number of legs that I am making, I’ll either set my finger gauge or use proper marking gauges set to those gauge points. One for the corner of the full-width octagon, one for the 1/7th taper and possibly one for the center point of the face.
Then I gauge all of the corner lines for the full-width octagon in the tenon area. I like my legs to taper to the floor. So the full-width octagon portion will be at the base of the tenon.
Then I mark the midpoint of each face on the same end of the leg.
Then I use a miter gauge or straightedge to connect those midpoints to create the 5/7th square.
Then I gauge the 1/7th taper for each side.
Finally, I draw connecting lines from the corners of the full-width octagon down to the midpoint on the end of the leg. So two lines are drawn on each face of the leg.
The only other layout takes place on the top of the leg. There I draw a target circle in the center to aid in removing material prior to final shaping of the tenon in the tapered tenon cutter.
Next up is the cutting.
With the drawknife at the shaving horse, I remove all for corners down to my layout lines.
This reveals the 5/7 square at the foot end of the leg.
All that is left is to remove the small amount of wood from the four new corners. I do this by eye since there is so little wood that needs to be removed.
Then I hog off the wood to rough in the tapered tenon at the top of the leg.
Then refine the tenon with the Veritas tapered tenon cutter.
Then a little cleanup work with a plane.
Here you can see the progression from layout to finished leg.
Well there you are, the OCTA-LEG-PRO gauge. I know there are lots of ways to layout and cut a tapered, octagonal leg, but this one works well for me and satisfies my proportional design requirement. It will simplify the layout process as well as standardize the cutting process. This should result in all of the legs of my staked furniture projects having a similar appearance.
I also gave the whole video thing another try. I’m still on the fence, but video is not as bad as I thought it would be. Anyway, have a watch and hit the “Like” button if you are so inclined. Also, if you would be so kind, leave a comment as to the good, bad and/or ugly. It will help with my fence straddling. 😉