Tag Archives: Hillbilly Tansu Project

HB Tansu #3-Progress 15

Posted on April 12, 2015 by Greg Merritt

My time in the shop was short today.  The onset of warm weather signals the start of grass mowing season.  It takes, on average, 3hrs to mow down the grass on my property.  Luckily I can now split that time … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , , | 6 Comments

HB Tansu #3-Progress 14

Posted on April 11, 2015 by Greg Merritt

I started my day in the shop by gluing and pegging the two drawers that I had ready.  I tend to build drawers one or two at a time.  It’s not the most efficient way of doing them, but i … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 10 Comments

HB Tansu #3-Progress 13

Posted on April 10, 2015 by Greg Merritt

Let the drawer making commence! Last evening I started with the drawer construction.  I would have liked to cut at least one practice joint in the walnut before diving into the real deal so that I could get a feel … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , , | 5 Comments

HB Tansu #3-Progress 12

Posted on April 7, 2015 by Greg Merritt

I was able to slip down t the shop for about an hour after work the past couple of evenings and size, cut and fit the drawer fronts the current HB Tansu.  One the aesthetic elements that originally drew me … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , , | 14 Comments

HB Tansu #3-Progress 11

Posted on April 5, 2015 by Greg Merritt

Today was carcass glue-up day.  There are a lot of parts involved in this and its always a little unnerving.  Everything needs to go together smoothly or I risk glue freeze on a joint somewhere.  Wouldn’t be the end of … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , , | 12 Comments

HB Tansu #3-Progress 10

Posted on April 4, 2015 by Greg Merritt

Today was all about panels.  I cut and fit all of the required panels for the carcass.  This isn’t a difficult job, but due the small size of my shop, can be tedious.  Constantly moving the assembly and the raw panel material. … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 6 Comments

HB Tansu #3-Progress 9

Posted on April 3, 2015 by Greg Merritt

I’ve been lucky with the weather this week.  It has been warm just about every evening when I came home from work.  So I was able to get an hour or so in the shop a few evenings.  Over the … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 8 Comments

HB Tansu #3-Progress 8

Posted on March 29, 2015 by Greg Merritt

I jolted awake in the wee hours of the morning with a sobering realization.  I hadn’t ordered any plywood panels for this tansu.  Which meant that I was pretty much dead in the water until I had ply in hand. … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 8 Comments

HB Tansu #3-Progress 7

Posted on March 28, 2015 by Greg Merritt

Finally some shop time!  It’s still getting cold at night here.  Below freezing at night cold.  So I planned ahead and turned the space heater in the shop on low last night before I went to bed.  This morning the … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 8 Comments

HB Tansu #3-Progress 6

Posted on March 22, 2015 by Greg Merritt

I spent Saturday completing the side rail joinery.  Basically just more of the same like I posted in Progress 5.  With the side rails completed, I turned my attention to the front and rear bearers. The first step was to … Continue reading →

Posted in Hillbilly Tansu-002 | Tagged , | 9 Comments